EFFECT OF HOLDING TIME IN THE PACK CARBURIZING PROCESS ON THE MECHANICAL PROPERTIES OF AISI 1045 STEEL

Muhamad Denny Setiawan(1*)


(1) institut teknologi indonesia
(*) Corresponding Author

Abstract


This study aims to determine the effect of holding time on the pack carburizing process using mixed media from coconut shell charcoal and beef bone powder with a composition of 70% coconut shell charcoal and 30% beef bone by volume. The pack carburizing process was carried out at a temperature of 950°C with a variation of heating time of 1, 3 and 5 hours, then a fast immersion process was carried out in water. To determine the effect of time eliminated on the process, hardness and metallographic tests were carried out. The test results showed that the chemical composition of the steel sample used in this study was AISI 1045 steel with a carbon content of 0.40%. In addition, the maximum average hardness test results were obtained for the material that underwent a solid carburizing process with a 5-hour elimination time of 346 HV (Hardness Rockwell), with the phases formed in the samples undergoing the pack carburizing process were ferrite, pearlite, and Partly there is a martensite phase.


Keywords


Carburizing, Charcoal, Cow bone, Carbon steel, Material

References


Andika Wisnujati. (2017). Analisa perlakuan carburizing terhadap sifat fisik dan mekanik pada bahan sprocket imitasi sepeda motor. Jurnal SIMETRIS, Vol 8 No 1. Retrieved from https://jurnal.umk.ac.id/index.php/simet/article/view/844

Darmo, S. (2018). Study on mechanical properties of pack carburizing SS400 steel with energizer pomacea canalikulata lamarck shell powder. urnal Internasional Bereputasi (Scopus Q3) International Journal of Mechanical Engineering and Technology (IJMET), 9(5), 14-23. Retrieved from http://eprints.unram.ac.id/23980/

Glyn, et.al. 2001. Physical Metallurgy of Steel. Class Notes and lecture material. ForMSE 651.01.

Hidayat, R. (2019). Pengaruh variasi holding time pada heat treatment tempering terhadap kekerasan dan kekuatan tarik baja AISI 1045 (Doctoral dissertation, University of Muhammadiyah Malang). Retrieved from https://eprints.umm.ac.id/57403/

Nwoke, V. U., Nnuka, E. E., Odo, J. U., & Obiorah, S. M. O. (2014). Effect of process variables on the mechanical properties of surface hardened mild steel quenched in different media. International journal of scientific & technology research, 3(4), 388-398.

Prasetyono, B., Hartono, P., & Marlina, E. (2017). Pengaruh variasi waktu tahan carburizing terhadap sifat mekanis baja aisi 1045 dengan media pendingin air tds nol. Jurnal Teknik Mesin, 5(01). Retrieved from http://download.garuda.kemdikbud.go.id/article.php?article=1753938

Yuliana, R., Rahim, E. A., & Hardi, J. (2017). Sintesis hidroksiapatit dari tulang sapi dengan metode basah pada berbagai waktu pengadukan dan suhu sintering. KOVALEN: Jurnal Riset Kimia, 3(3), 201-210. Retrieved from https://bestjournal.untad.ac.id/index.php/kovalen/article/view/9329


Article Metrics

Abstract view : 115 times


DOI: https://doi.org/10.26714/traksi.23.2.2023.239-246

Refbacks

  • There are currently no refbacks.


Copyright (c) 2024 TRAKSI

Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 International License.


TRAKSI : Majalah Ilmiah Teknik Mesin

ISSN : 1693-3451 (Pinted) e-ISSN : 2579-9738 (Online)

Published by: LP2M Unimus bekerjasama dengan APTI (Asosiasi Profesi Teknik Indonesia)  

 
ADDRESS

Jl. Kasipah No. 12 Semarang

E-mail: [email protected] Call: 0248445768


Sponsors

Asosiasi Profesi Teknik Indonesia (APTI)

Website: www.apti.or.id