OPTIMASI SETTING PARAMATER CLEANLINESS, KETEBALAN, DAN JENIS CAT PADA MATERIAL BAJA A572 TERHADAP DAYA REKAT CAT

Farizi Rachman(1*), Bayu Wiro Karuniawan(2), Anggie Madhu Firdiandani(3)


(1) Teknik Desain dan Manufaktur, Politeknik Perkapalan Negeri Surabaya (PPNS)
(2) Teknik Desain dan Manufaktur, Politeknik Perkapalan Negeri Surabaya (PPNS)
(3) Teknik Desain dan Manufaktur, Politeknik Perkapalan Negeri Surabaya (PPNS)
(*) Corresponding Author

Abstract


The manufacturing process consists of several stages, one of them is the finishing stage. The finishing stage at PT. Supra Surya Indonesia consists of surface preparation process and painting process. The adhesion of the paint must meet the criteria to get good protective quality for the product. In the painting process, there are always defective products that must go through the repair stage before packing. Process parameters such as cleanliness level of the material surface and paint thickness need to be considered and the selection of the type of paint will affect the results of painting. Based on the problems above, it is necessary to research the analysis of process parameters that can optimize the value of paint adhesion. This study uses the Taguchi method so that the contribution of cleanliness parameters is 49.6995 %, paint thickness is 5.0014 %, and paint type is 40.4139 %. The optimum combination of parameters is cleanliness Sa 2 1/2, the thickness of 100 µm, and the type of phenolic epoxy paint.


Keywords


adhesion of paint, thickness, paint type, painting, cleanliness

Full Text:

PDF

References


Schmidt, R. G., & Bell, J. P. (2005). Epoxy Adhesion to Metals. Advances in Polymer Science, 33–71. doi:10.1007/bfb0017914

Corrosion Care Indonesia (2006). Coating Inspector Muda. Bandung, Indonesia : ASCOATINDO.

Prihantono, Y. B. (2020). Analisa Daya Rekat Cat pada Proses Painting dengan Variasi Parameter Dust Level, Temperatur, dan Kekasaran Permukaan pada Baja A36 Menggunakan Metode Taguchi. Tugas Akhir Jurusan Teknik Desain dan Manufaktur. Politeknik Perkapalan Negeri Surabaya.

Pratama, R. A., & Kromodiharjo, S. (2017). Studi Eksperimen Pengaruh Tebal Cat dan Kekasaran pada Pelat Baja Karbon Rendah Terhadap Kerekatan Cat dan Biaya Proses di PT. Swadaya Graha. Jurnal Teknik ITS, 5(2).

Dewangan, S., & Biswas, C. K. (2013). Optimization of machining parameters using grey relation analysis for EDM with impulse flushing. International Journal of Mechatronics and Manufacturing Systems, 6(2), 144–158.

Vikas, Roy, A. K., & Kumar, K. (2014). Effect and optimization of various machine process parameters on the surface roughness in EDM for an EN41 material using Grey-Taguchi. Procedia Materials Science, 6, 383–390. https://doi.org/10.1016/j.mspro.2014.07.049

Ender Hazir , Sedanur Seker , Kucuk Huseyin Koc , Tuncer Dilik , Emine Seda Erdinler & Emel Ozturk (2020): Optimization of plasma treatment parameters to improve the wood-coating adhesion strength using Taguchi integrated desirability function approach, Journal of Adhesion Science and Technology, DOI: 10.1080/01694243.2020.181666

ASTM D4541-17 (2017). Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers. ASTM International. West Conshohocken, PA.

Montgomery, A.A. (2013). Introduction to Statistical Quality Control, 6th ed.John Wiley & Sons, Arizona State University.

Soejanto, I. (2009). Desain Eksperimen dengan Metode Taguchi. Yogyakarta, Indonesia: Graha Ilmu


Article Metrics

Abstract view : 408 times
PDF - 72 times

DOI: https://doi.org/10.26714/jsunimus.9.2.2021.96-100

Refbacks

  • There are currently no refbacks.


Copyright (c) 2022 Jurnal Statistika Universitas Muhammadiyah Semarang

Editorial Office:
Department of Statistics
Faculty Of Mathematics And Natural Sciences 
Universitas Muhammadiyah Semarang

Jl. Kedungmundu No. 18 Semarang Indonesia



Published by: 
Department of Statistics Universitas Muhammadiyah Semarang

View My Stats

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License